- 1
- 2
歐洲進口工業設備
五金工具建材
機械
泵閥儀表
儀器儀表
模擬盒藥物測試安全表校準器組合式測試設備控制系統硬度計熱交換器掃描器沾污儀紫光源混合器萬用表百分表風速儀分度盤放大器六分儀熱像儀拐檔表數顯表檢測儀木材測濕儀電子秤靜電消除器真空計壓力表進樣器移液器剩磁探測測試儀擺動缸濾芯測力計打標機試驗機混合機平衡器溫控器壓力氣壓張力能量計報警器測距儀定位器熒光儀編碼器注射器打印機液位計折光儀流量計感應機探測器檢測器超聲波發生器濕度計傳感器聯軸器烘烤設備檢漏儀制冷機輻射測溫傳輸探頭光譜儀射線干燥器發射器指南針印刷設備操作面板顯示器粘度計量塊調節器采樣記錄儀油位計料位計冷卻分析溫度計壓差測量發生器電子電工
壓力開關
實驗室設備
| 德國IDEAL閃光對焊機 BAS 040 |
| 點擊次數：1771 更新時間：2021-07-05 |
德國IDEAL閃光對焊機 BAS 040
產品說明： 德國IDEAL Bandsaw Flash Butt Welder te BAS 040 BAS040型IDEAL閃光對焊機
for flash butt welding of 閃光對焊的適用范圍：
Metal bandsaws (bi-metal, carbon steel bandsaws, tungsten bandsaws) 3 - 27 mm 金屬帶（雙金屬，碳鋼帶鋸，鎢合金帶鋸） Meat and fish bandsaws(stainless steel) 5 - 20 mm 肉和魚帶鋸刀片（不銹鋼） Wood bandsaw 5 - 40 mm 木頭帶鋸刀片 Band knives 5 - 20 mm 帶形刀 (The above mentioned dimensions refer to a minimum strip thickness of 0,4 mm) （以上尺寸所涉小厚度為0.4毫米及以上。） Capacity of transformer at 50 % duty cycle 3,5 kVA 變壓器額定容量（50%負載）
Machine description: 機器說明： Machine case made out of welded steel sheet with vertical cast iron face plate – high precision guide of the movable jaw – automatic control of the flashing cycle by the gear unit drive with notches – upsetting by means of a pile of cup springs – wide distance of jaws for annealing adjustable with lever – adjustment of weld current in 4 steps – electronic controlled annealing device for infinite adjustment of the anneal voltage – clamping device with manual levers suitable for band tools upto 40 mm width 機殼由焊接鋼板和垂直鑄鐵面板組成－移動顎的導向－由齒輪傳動裝置檔電弧周期自動控制；焊端頂緊由一束盤型彈簧實現－用于退火的顎寬用杠桿調節－焊接電流4級可調－電子控制退火裝置無限調節退火電壓－帶手動杠桿的夾緊裝置滿足40毫米寬的帶具；
IDEAL Square Cutter te AHE 050 AHE050型帶鋸直角切割器 for separate mounting to work table to produce burr-free, square cuts at bandsaw blades up to a width of 50 mm 單獨固定在工作臺上；帶寬達50 mm帶鋸刀片的刺直角切割；
IDEAL Special Grinding Machine te SMH 060 SMH060型磨邊機 for removing the weld burr - Grinder as separate unit to be mounted to customer work table - machine made for maximum band width of 60 mm - manual clamping device for band with weld joint - grinding by 3 phase motor and continously adjustable grinding wheel
去除焊疤－作為單獨裝置固定在用戶的工作臺上；適合帶寬60 mm；
工作原理: Working Principle:
The working principle of the imported welder: the working metal piece to be welded is pressed between two electrodes, when the power is on, the energe(current) generates, and flows through the work piece contact surface and the adjacent zone, resulting in resistant thermal effects which heat the work piece into molten or plastic state, thus plays the function of welding the metal.
本次的焊接機的工作原理為：是將被焊（金屬）工件壓緊于兩電電子之間，通電后產生的能量（電流），利用電流流經工件接觸面及鄰近區域產生的電阻熱效應將其加熱到熔化或塑性狀態，從而起到焊接金屬的功能。
|
18804209403
首 頁